Meat Grinders

Our selection of meat grinders are ideal for your lower-volume or high-volume needs. Transform your processing room with commercial-grade meat grinders

Meat Grinding Products

BIRO Model AFMG-56MK III Automatic Mixer Grinder

By using the BIRO Model AFMG-56MKIII Mixer-Grinder, you can start increasing the output of your grinding operation without having to spend a fortune.

The 800 lb. (362.9 kg) hopper gives you the kind of capacity you need; the 20HP (15 kW) auger motor gives you the power you need. The 5HP (3.7 kW) mixer motor is strong enough that it won’t bog down with a full hopper; the twin mixing paddles give you a thorough mix. Safety interlocks and a pneumatic lift for the lid help ensure safety; the machine has watertight controls and totally enclosed motors so you can do a full wash-down cleanup. The hopper and frame are constructed of heavy duty stainless steel so it resists damage and corrosion. As with all BIRO designed and built machines, you get the benefit of over 90 years of engineering experience in building meat processing equipment.

3/8″ (9.0 mm)

1/8″ (3.5 mm)

Model AFMG-24 Shown with optional adjustable legs with casters

Specifications

Model: AFMG-24 Automatic Grinder (chopper, mincer).
Construction: Stainless steel feed pan and polished stainless steel case, Cast iron hot tin dipped bowl, ring, and auger size 32.

CONSTRUCTION
Heavy duty stainless steel hopper, lid, paddles, frame and legs. Stainless steel Size 56 bowl, ring and auger.

SWITCH
Watertight magnetic controller with thermal overload and under voltage protection; separate mix and grind controls; product mix timer is factory preset for 2 minutes mix and 5 minutes off sequence.

POWER CORD
Wired on the low side (200-240) volt operation: 9’ (2.7 m) No. 4 GA. wire conductor Power Cord – less plug.
Wired on the high side (380-480) volt operation: 9’ (2.7 m) No. 8 GA. wire conductor Power Cord – less plug.
Wired (575) volt operation: 9’ (2.7 m) No. 10 GA. wire conductor Power Cord – less plug.

HOPPER CAPACITY
Up to 800 lbs. (363 kg).

GRINDING CAPACITY
Up to approximately 250 lbs. (113 kg) output per minute.

DRIVE SYSTEM
Auger – 20HP (15 kW) T.E.F.C. industrial motor, single reduction silent chain. Mixer feed paddles – 5HP (3.7 kW) T.E.F.C. heavy duty double reduction gear box and heavy duty open face gear drive.Safety: Magnetic safety interlock on hopper lid.

SAFETY
Magnetic safety interlock system on hopper lid.

STANDARD FEATURES
Hopper without side feed inlet • preset pneumatic (45 P.S.I.) lid opener on right side (when facing bowl) • stainless steel spurt guard • ring wrench • operating and safety manual • 11” (280 mm) stainless steel adjustable threaded legs mounted on floor pads. NOTE – If machine is raised to 8” (203 mm) or more of exposed threads, the machine must have reinforcing cross leg brace (#60142NE).

OPTIONS (NC)
Pneumatic lid opener (45 P.S.I.) on left side (when facing bowl).

OPTIONS (EC)
Size 56 knife and plate • 6” (152 mm) diameter swivel side lock castors • 11” (280 mm) stainless steel adjustable studs mounted on castor pads. NOTE – If machine is raised more than 8” (203 mm) of exposed thread a stainless steel cross brace (#60142NE) is required. Hopper view, fold up step on left or right side 18”Wide (46 cm) x 19-¾” Deep (50 cm) • continuous feed grill style lid (in place of std. flat lid), right or left lid opening • also available with conveyor product feed chute mounted on right, rear or left side of grill lid.

KNIFE / PLATE
Required, extra cost, various plate hole sizes available to fit your specific application (see above). Call agency or factory.

TANDEM OPTIONS (EC):
Requirements for Tandem Operation: Size 56 to 56 right or left side hopper 90° product feed inlet • Size 56 to 56 discharge horn, horn seal, and connecting bracket • 14” (35.6 cm) O.A.L. adjustable leg assembly mounted on 4 castor pads (cross brace and castors required, see above options).

CERTIFICATION
C.F.I.A

WEIGHT (7.5 HP VERSION)
Uncrated 1800 lbs. (817 kg) approx. Wood crated: 2526 lbs. (1146 kg) approx.

DIMENSIONS CRATED
L = 73” (185 cm), W = 65” (165 cm), H = 82” (208 cm).

Item Number      LIT-AFMG-56 MK III-309

Motors

Motor HP KW TYPE VOLTS AMPS CYCLE PH STATUS
Auger 20 15 TEFC 208-230/460 53-48/24 60 3 STD
Mixer 5 3.7 TEFC 208-230/460 14-13/6.6 60 3 EC
Auger 20 15 TEFC 200 55 60 3 EC
Mixer 5 3.7 TEFC 200 15.9 60 3 EC
Auger 20 15 TEFC 575 26 60 3 EC
Mixer 5 3.7 TEFC 575 5.2 60 3 EC
Auger 20 15 TEFC 220/380-415 56/29.3-27 50 3 EC
Mixer 5 3.7 TEFC 220/380-415 14/8.1-7.4 50 3 EC

TEFC=Totally Enclosed Fan Cooled STD=Standard EC=Extra Cost

Browse Our Full Shop

We are committed to providing our equipment customers with reliable service for the machines purchased through our distribution network.

Townsend, GA

Headquarters

Stalmic Distributors Inc
1268 Ga Highway 99
Townsend, GA 31331

Lakeland, FL

Warehouse

Stalmic Distributors Inc
Lakeland , FL 33801

Stalmic Distributors Inc is located in Townsend, Georgia. This organization primarily operates in the Processing and Packaging Equipment business / industry within the Wholesale Trade - Durable Goods sector.